Meet the Keenon C55

The Keenon C55 sweeps, scrubs and dust-pushes in a single pass, covering up to 2,376 m² an hour and as much as 11,880 m² on one charge. It is built for indoor spaces of 3,000 m² and up: airports and transit hubs, shopping malls, exhibition halls, factories, warehouses and large office campuses.

In spaces that size, the cost of cleaning comes from distance, refills and downtime. The C55 is designed to cut all three.

Sweeper and scrubber in one pass

Most large sites run a sweeper first and a scrubber after. The C55 combines both into one machine with a three-brush drum design, so sweeping and mopping happen in the same trip. It runs three modes:

  • Sweep & wash: a front pre-sweep picks up debris, then a rear roller brush scrubs the floor and re-sweeps behind itself
  • Sweep & push: sweeping plus dust pushing, for dry daily maintenance over long runs
  • Water suction: pulls standing water off the floor

The roller brush presses down with 18 kg of force across a 550 mm cleaning path, enough for the ground-in dirt that high-traffic floors collect.

Twice the water, fewer trips to the tap

On a large floor, every refill stop is lost cleaning time. The C55 carries a 60 L clean water tank and a 47 L sewage tank, about twice the capacity of similar machines in its class. That means fewer interruptions and longer unattended runs.

Up to 21 kPa of suction pulls dirty water back off the floor after scrubbing. Dry debris goes into a 2 L front dust box, plus a 0.7 L rear box on the roller-brush version. The water tank uses a reversible shell design.

Safe at speed in busy spaces

A 150 kg robot moving at up to 1.2 m/s has to see everything around it. The C55 positions itself with VSLAM and protects its path with a layered sensor set:

  • Laser radar and 3D radar for mapping its surroundings and detecting obstacles
  • Stereo vision and an RGB camera for seeing people and objects
  • Line laser for low obstacles near the floor
  • Anti-collision sensors and fall protection as a last line of defense

It detects objects as small as 70 × 70 × 50 mm and stops within 0.5 m from 0.6 m/s, wet or dry. It can clean right up to edges with zero gap.

On the move, it rolls over 50 mm speed bumps, crosses 35 mm trenches and climbs 10 mm vertical obstacles when fully loaded. It needs a 950 mm lane to run straight and 1,250 mm to turn around.

Two batteries, five-second swaps

The C55 holds two 25.6 V, 50 Ah lithium iron phosphate batteries in a dual-battery compartment. A full charge runs it for up to 5 hours of sweeping and scrubbing, or up to 10 hours of sweeping and dust pushing.

Charging from empty takes about 4 hours, but the robot doesn’t have to wait. Either battery can be swapped in about 5 seconds, so a site with spare packs can keep the C55 working across shifts.

An optional automatic docking station goes further. The robot docks itself to charge, refill clean water and drain the sewage tank, with no one on hand.

Simple to run, quick to service

Operators work the C55 through an 11.6-inch touchscreen, with a dot-matrix status display, interactive lights and voice announcements. People nearby can see and hear what it is doing.

Consumables are quick-switch, and the brushes slide out on rails for fast removal. Upkeep takes minutes, not a maintenance shift.

The Keenon mobile app and Keenon Cloud manage the fleet:

  • Immediate, scheduled and manual cleaning, plus a teaching mode for new routes
  • Break-point resumption, so an interrupted job continues where it stopped
  • Auto-recharging, IoT integration and multi-device coordination
  • App available in Chinese, English, Japanese, Korean, French, Thai and German

C55 at a glance

SpecC55
Cleaning efficiencyUp to 2,376 m²/h (including side brush)
Working area per runUp to 11,880 m²
Cleaning width550 mm (with roller brush)
Max cleaning speed1.2 m/s
SuctionUp to 21 kPa
Brush pressure18 kg
Water tanks60 L clean, 47 L sewage
Dust boxes2 L front; 0.7 L rear (roller-brush version)
RuntimeUp to 5 h sweep & scrub; 10 h sweep & dust push
Battery2 × 25.6 V, 50 Ah LFP; about 4 h to full charge
Noise≤70 dB(A) at mid setting
SlopeUnder 2° while cleaning; 6° when not cleaning
Size and weight860 × 850 × 1,082 mm (including squeegee); 150 kg
Operating conditionsIndoors, 1–40 °C, 20–80% RH
FinishABS and PP, moon rock gray

Is the C55 right for your site?

The C55 suits large, open, hard-floored spaces where floors take daily sweeping and regular scrubbing. Think of sites well over 3,000 m² with wide aisles. For smaller or tighter spaces with mixed carpet, the compact Keenon C40 is the better fit.

Plan for its size. The C55 needs 950 mm lanes and 1,250 mm to turn, it cleans on slopes under 2°, and it is built for indoor use only.

If your crews spend each night walking ride-on or push scrubbers across thousands of square meters, the C55 can take that work over. Contact us to book a demo on your own floors.

Meet the Keenon C40: A 4-in-1 Cleaning Robot Built for Real-World Spaces

The Keenon C40 sweeps, vacuums, dust mops and scrubs on its own, covering up to 1,100 m² an hour. It is built for the spaces that big industrial scrubbers can’t reach and small consumer robots can’t handle: offices, clinics, hotel lobbies, retail floors and schools.

In these spaces, floors mix carpet and hard surfaces, corridors are tight, and people are always walking through. Here is how the C40 is designed to deal with all three.

Four jobs, one machine

One robot replaces a rotation of separate tools. The C40 runs five modes:

  • Sweeping for loose debris, with double side brushes widening the path to 560 mm
  • Vacuuming (sweep + vacuum) for carpet and hard floor, into an 8 L dust bag
  • Dust mopping (sweep + dust mop) for fine dust on hard surfaces
  • Scrubbing (sweep + scrub) for wet cleaning, fed by a 16 L clean water tank
  • Water extraction to pull standing water off the floor

The key to switching between dry and wet work is Keenon’s triple-brush dry/wet separation system. Dry debris and dirty water travel separate paths, so they never mix. That means no muddy slurry in the dust bag and no clogged wet system, and the robot can move from vacuuming to scrubbing in one step.

Dry floors seconds after scrubbing

Wet floors are a slip hazard and a reason to rope off an area. The C40’s answer is 23,500 Pa of suction, strong enough to leave the floor dry within seconds of scrubbing, with no water residue.

That suction pulls dirty water into an 11 L wastewater tank. The tank is fully removable and washable, so it can be rinsed out properly after each shift instead of building up odor and bacteria.

Built to work around people

The C40 is meant to clean during business hours, not just after everyone leaves. To do that safely, it fuses data from several sensor types:

  • LiDAR for mapping and positioning, with a detection range of up to 40 m
  • Stereo vision sensors with 170° horizontal coverage
  • Line laser and ultrasonic sensors for close-range and low-lying obstacles
  • VSLAM, an IMU, an RGB camera and a collision sensor to round out the picture

Keenon’s navigation and obstacle-avoidance software combines these into centimeter-level positioning, tuned for spaces shared with people.

The footprint helps too. The robot is 616 × 550 × 690 mm and fits through gaps as narrow as 65 cm and under clearances as low as 75 cm. It crosses 35 mm gaps, climbs 15 mm thresholds when navigating or vacuuming, and handles low-pile carpet up to 10 mm.

Long runtimes, and swaps instead of waits

The C40 runs on a 25.6 V, 50 Ah LFP (lithium iron phosphate) battery. Runtime depends on the job:

ModeRuntime (up to)
Sweeping15 h
Dust mopping10 h
Vacuuming6 h
Scrubbing5 h

A full charge takes about 2 hours. For sites that can’t afford that downtime, the battery is quick-swappable: drop in a charged pack and the robot is back at work with almost no interruption.

Charging works two ways. A bundled charger handles manual charging, and an optional charging pile (sold separately) lets the robot dock and recharge itself, then resume where it left off.

Easy to run, easy to maintain

Staff don’t need training in robotics to use the C40. Setup and daily use run through an 11.6-inch HD touchscreen (1920 × 1080), with light, touch and voice prompts. A rear-tilting control panel lets an operator stand behind the robot and drive it manually for spot cleaning.

Routine upkeep is designed to be fast. Side brushes, the dust bag and both water tanks are quick-switch consumables, and the brushes sit on rails that slide out for cleaning.

For managers, the Keenon mobile app and Keenon Cloud handle the rest:

  • Immediate, scheduled and manual cleaning, plus a teaching mode for new routes
  • Breakpoint resumption, so an interrupted job picks up where it stopped
  • Auto-recharging and multi-robot coordination across a site
  • Connectivity over Wi-Fi or 4G, with the app in Chinese, English, Japanese, Korean, French, Thai and German

C40 at a glance

SpecC40
Cleaning efficiencyUp to 1,100 m²/h
Cleaning area per runUp to 3,000 m² vacuuming; 2,500 m² scrubbing
Cleaning width560 mm sweeping; 400 mm vacuuming and scrubbing
SuctionUp to 23,500 Pa
Dust capacity8 L dust bag + 0.7 L dustbin
Water tanks16 L clean, 11 L dirty
Max speed0.8 m/s (1.2 m/s planned via future upgrade)
Noise70 dB
SlopeUp to 2° while cleaning; 8° navigation only
Size and weight616 × 550 × 690 mm; 70 kg (with battery, tanks empty)
Operating conditionsIndoors, 0–40 °C, 20–80% RH
MaterialsABS and aluminum alloy

Is the C40 right for your space?

The C40 fits best where floors are mixed, spaces are 1,000–3,000 m², and cleaning has to happen around people. Think office floors, healthcare waiting areas, hotel lobbies and corridors, retail stores, and school buildings.

It is less suited to large warehouses, steep ramps or deep-pile carpet. Cleaning slopes top out at 2°, and carpet handling is rated for low pile up to 10 mm.

If your team spends hours each day pushing separate sweepers, vacuums and scrubbers, the C40 can take that routine work off their hands. Contact us to book a demo and see it clean your floors.

Meet the KLEENBOT C30: Smart Commercial Cleaning Robot

The KLEENBOT C30 cleans up to 600 m² of floor an hour, on its own, with 19,000 Pa of suction behind it. It is a commercial cleaning robot built for the large, busy floors that eat up staff hours: hotel lobbies, offices, shopping centers, airports and hospitals.

One charge covers up to 2,500 m² per task. When the battery runs low, the C30 drives itself back to its charging pile. Your team sets the schedule once and gets back to work that needs a person.

Here is what the C30 does, the numbers behind it, and how to put it to work.

Why the C30 is a Smarter Commercial Cleaning Robot.

Two cleaning modes in one machine. Vacuuming mode runs the vacuum and sweeper together to pull up dust and debris. Dust mopping mode runs quieter and longer, up to 10 hours on a single charge, for daily touch-ups on hard floors.

Wide coverage on every pass. Two side brushes and a rolling brush give the C30 a 610 mm cleaning path. It reaches edges and corners, not just open floor.

Strong suction for real dirt. At up to 19,000 Pa, the C30 handles hard floors and low-pile carpet up to 10 mm thick. Debris goes into a 3.5 L dust bag, and a HEPA filter traps fine particles.

Smart, precise navigation. LiDAR, stereo vision sensors, a collision sensor and an inertial measurement unit (IMU) work together. The C30 maps your space with centimeter-level accuracy and spots obstacles up to 25 m away.

Safe around people. Top speed is 0.8 m/s, it stops within 50 cm, and it runs at 70 dB or less. It can climb 20 mm thresholds and handle slopes up to 8°.

Easy to run. A 7-inch touchscreen and an app in five languages (English, Chinese, Japanese, Korean and French) control everything. A customizable expression screen lets the robot greet guests or show your own content as it works.

Specifications

All figures come from the official C30 datasheet (V1.2). Battery life depends on the floor and the job.

Performance

SpecC30
Cleaning modesVacuuming (vacuum + sweep), Dust mopping
Cleaning efficiencyUp to 600 m²/h
Area per chargeUp to 2,500 m² per task
Suction powerUp to 19,000 Pa
Cleaning width610 mm (2 side brushes + rolling brush)
Dust bag3.5 L
Battery life3–6 h vacuuming; up to 10 h dust mopping
Noise≤ 70 dB
Top speed0.8 m/s
Braking distance50 cm
Obstacle climbing20 mm
CarpetLow-pile, up to 10 mm
SlopeUp to 8°

Battery and charging

SpecC30
BatteryLFP (lithium iron phosphate), DC 25.6 V, 28.5 Ah
ChargingAutomatic, with the included charging pile
Charging input100–240 V, 50/60 Hz
Charging time5–6 h

Hardware and software

SpecC30
BodyABS and aluminum alloy
PositioningLaser, centimeter-level accuracy
SensorsLiDAR, stereo vision, collision sensor, IMU
LiDAR range240°, up to 25 m
Stereo vision range120°, 0.1–1.5 m
NetworkWi-Fi, 2.4 GHz
Screen7 in, 1024 × 600 touchscreen
Operating systemLinux (control) and Android (interaction)
App languagesEnglish, Chinese, Japanese, Korean, French
App functionsImmediate, scheduled, manual cleaning; teaching mode

Size and environment

SpecC30
Dimensions (W × D × H)490 × 610 × 750 mm with dust push; 490 × 520 × 750 mm without; 490 × 646 × 990 mm handle raised
Weight35 kg with battery; 30 kg without
Charging pile220 × 130 × 330 mm, 2.4 kg
Operating conditionsIndoors, 0–40 °C, 20–80% RH
Storage conditions−15 to 45 °C, 20–80% RH
ColorPearl White

Putting the C30 to work

Where it fits

The C30 is made for indoor commercial spaces with hard floors or low-pile carpet:

  • Hotels: lobbies, corridors and ballrooms, cleaned overnight or between events
  • Offices: open-plan floors and meeting areas, cleaned before staff arrive
  • Retail and malls: wide walkways that need daily attention
  • Airports and transit hubs: large concourses with steady foot traffic
  • Hospitals and clinics: quiet operation and HEPA filtration suit sensitive areas

Getting started

  1. Unbox and set up. Place the charging pile against a wall in an open spot. Fit the side brushes and confirm a dust bag and HEPA filter are in place.
  2. Map your space. Use teaching mode to guide the C30 through the area once. It builds a map with centimeter-level accuracy.
  3. Pick a mode. Choose vacuuming for deep cleans and carpet, or dust mopping for long, quiet sessions on hard floors.
  4. Set the schedule. Use the app or the 7-inch screen to clean now, on a schedule, or manually.
  5. Let it run. The C30 avoids people and obstacles, then returns to its charging pile on its own.

Keeping it running

Empty or replace the 3.5 L dust bag when full, and check the brushes and HEPA filter regularly. Side brushes, mopping cloths, rolling brushes, roller brush scrapers, dust bags and HEPA filters are all sold as replacement parts.

In the box

ItemQty
C30 robot1
Charging pile1
Product manual1
Side brushes4
Rolling brushes2
Mopping cloths2
Roller brush scrapers3
Dust bags20
HEPA filter1

The bottom line

The KLEENBOT C30 pairs strong suction and a wide cleaning path with long battery life and smart navigation. It covers up to 2,500 m² on one charge and recharges itself, so your floors stay clean while your team focuses on guests and customers.

Ready to see it on your floor? Contact us to book a demo or get a quote for the KLEENBOT C30.

Source: KLEENBOT C30 Datasheet V1.2 (April 2025). Actual results may vary by environment.